NLENFor installers

Connect it yourself in about twenty minutes

The Nymo sits between the socket and your electric water heater, and a small box clicks into your smart meter. Nothing else needs to be routed through the house.

Prefer to have it done for you? That’s also possible →

Someone takes the sensor out of the box, with the Nymo and the manuals on the table

Can you do it yourself?

That depends on five things. Check them before you order.

  • Do you have an electric water heater without smart functions?

    You set the temperature with a dial (mechanical thermostat): no display, no timer, no app. Heat pump boilers and smart boilers do not work.

  • Is your electric water heater single-phase and maximum 3,000 watts?

    That applies to almost every standard electric water heater.

    Where can I find that?

    On the rating plate: a sticker or plate on the side or bottom of the electric water heater. It shows the power in watts (for example 2,000 W or 2,400 W) and the voltage. If it says 230 V, then it is single-phase: that is a standard domestic connection. At 400 V it is three-phase power, and then the Nymo will not work.

  • Is your electric water heater plugged into a socket?

    Then you don't need an extra socket. The Nymo uses the same one: the plug from the electric water heater goes into the Nymo, and the Nymo into that socket.

    And if the electric water heater is hardwired?

    Then one socket must be added near the electric water heater, or an electrician can hardwire the Nymo in the same place. That is a half-hour job, and it is the only thing you might need an electrician for.

  • Is the P1 port of your smart meter free?

    That is where the box goes that measures how much surplus you have.

    Which port is that?

    Every smart meter has a P1 port: a small input for a plug, like a telephone cable, often behind a cover at the bottom or side. If something is already plugged in, for example from an energy app or your energy provider, then you can order a splitter from us so they can both be used.

  • Does it fit your heating system?

    Almost always: combi boiler, hybrid or electric heat pump, district heating. Only the exact details of what changes will vary.

    How does it work for me?

    If you have a gas combi boiler, it will top up the heat if the sun hasn't quite managed it. With a heat pump with a buffer tank (a storage tank for hot water), the Nymo feeds the heating element inside it. With district heating, the electric water heater works independently of the heat network. View all five setups →

Install in three steps

Once the electric water heater is mounted and filled, the Nymo itself takes about twenty minutes.

  1. Mount the electric water heater

    Follow the standard instructions for the electric water heater: on the wall or floor, connect the water, bleed the system. This is the only part where you might get wet. If you're unsure, feel free to have it done for you.

    If you order the electric water heater from us, the mounting materials for your chosen location are included.

    An electric water heater from Tesy, not yet with Nymo
  2. Click the sensor into your smart meter

    The small box goes into the P1 port of your smart meter using the included cable. That’s it: it gets its power from that same port.

    The sensor and the Nymo find each other wirelessly, so no cable is needed from the consumer unit to the electric water heater.

    Someone holds the sensor near the smart meter in the consumer unit
  3. Put the Nymo in between

    The Nymo goes between the socket and the electric water heater: plug the electric water heater into the Nymo, and the Nymo into the socket. From that moment on, it determines how much power the electric water heater receives.

    Is the electric water heater hardwired instead of using a plug? Then an electrician can connect the Nymo in the same place.

    Someone inserts the Nymo plug into the socket, next to the electric water heater

After that, you don't have to do anything. If there is a surplus, it goes to your electric water heater; if there is nothing left over, nothing happens.

Need some help?

The installation manual shows every step with diagrams. If you get stuck, we’re happy to help.

An installer connects the pipes of a horizontal electric water heater, with the Nymo on the wall above it

Prefer to have it done for you?

A partner in your area will mount the electric water heater, connect the Nymo, and test that everything works before they leave.

Request a free quote